I was trying to install RGH on xbox 360 (PHAT) but know with original nand and without the glitch chip i have RROD error code 0001 any ideas? i was reading something about the mosfets! I dont know :S
↧
RROD After RGH :(
↧
Trinity Dual Nand QSB Fail?
I just installed a Dual Nand QSB and i'm gett zero Power now..
I got it soldered in and Plug in press sync fast nothing happens..
I've installed maybe other brand Dual Nands. but this one for what ever reason doesn't want to work..
maybe you can see something i missed:
![]()
![]()
![]()
I know the Four points looks bad but i double check it with Flashlight..
I got it soldered in and Plug in press sync fast nothing happens..
I've installed maybe other brand Dual Nands. but this one for what ever reason doesn't want to work..
maybe you can see something i missed:
I know the Four points looks bad but i double check it with Flashlight..
↧
↧
Corona V2 dual nand?
I already get my corona v2 cpukey and ive installed the extra pcb nand ... whats next? i dont know how to inject xebuild in to my secondary nand :S
What am i supposed to do?
P.S in the original nand i have XELL!
What am i supposed to do?
P.S in the original nand i have XELL!
↧
corona add one R SVF file
i try this file and its work realy good with 25-30CM awg22 cable with out any CAP
and no need special route
so i share this info
and if someone have idea how to make it better i will be glad to know
THANKS
and no need special route
so i share this info
and if someone have idea how to make it better i will be glad to know
THANKS
↧
Is this the correct way to mod a Corona 250gb?
Hi,
Could somebody please just check that I have got the procedure correct to flash a Corona 250gb...
01) Bridge points for slim on squirt360, and bridge 220pf points.
02) Solder chip to board (cpu_rst, post, gnd, vcc, scl, sda).
03) Route cpu_rst according to photo, use a 55cm (awg24) wire.
04) Solder SPI points to allow onboard flashing (sd0, sck, gpio1, gpio0, sdi, cs).
05) Connect (Squirt) SPI flasher via ribbon cable.
06) Plug in power to 360.
07) Flash Correct .xvf to squirt360 chip (using autogg).
08) Read nand (using autogg).
09) Create NandXell (using autogg).
10) Flash NandXell (using autogg).
11) Boot console and grab key via http, because screen does'nt display with Corona).
12) Create nand image by using key and choosing dash (using autogg).
13) Flash image (using autogg).
If I have left something out or wrong, please post...
Thanks.
Could somebody please just check that I have got the procedure correct to flash a Corona 250gb...
01) Bridge points for slim on squirt360, and bridge 220pf points.
02) Solder chip to board (cpu_rst, post, gnd, vcc, scl, sda).
03) Route cpu_rst according to photo, use a 55cm (awg24) wire.
04) Solder SPI points to allow onboard flashing (sd0, sck, gpio1, gpio0, sdi, cs).
05) Connect (Squirt) SPI flasher via ribbon cable.
06) Plug in power to 360.
07) Flash Correct .xvf to squirt360 chip (using autogg).
08) Read nand (using autogg).
09) Create NandXell (using autogg).
10) Flash NandXell (using autogg).
11) Boot console and grab key via http, because screen does'nt display with Corona).
12) Create nand image by using key and choosing dash (using autogg).
13) Flash image (using autogg).
If I have left something out or wrong, please post...
Thanks.
↧
↧
RGH in XBOX Slim Trinity
Hi guys
I have installed a squirt in a xbox slim (trinity) but i dont get the xell. I am not sure if I have done it properly. Here is a pic:
http://i1099.photobucket.com/albums/...07F3BD7A37.jpg
But I have some issues:
- Led should blink? It is always turned on
- There are 4 timmings for Trinity, What do I have to choose?
- The diagram says that you have to bridge VCC and Pad3, should I do it?
Thanks in advance
I have installed a squirt in a xbox slim (trinity) but i dont get the xell. I am not sure if I have done it properly. Here is a pic:
http://i1099.photobucket.com/albums/...07F3BD7A37.jpg
But I have some issues:
- Led should blink? It is always turned on
- There are 4 timmings for Trinity, What do I have to choose?
- The diagram says that you have to bridge VCC and Pad3, should I do it?
Thanks in advance
↧
Squirt rev B
Hi everybody,
I noticed that during breaking the PCB panels of Rev B, the copper may or may not be "wide" enough (as in the distance between the pads and edges).
The consequence of this is minimal: the lower GND pad (near the LPT pads) is weakened and doesn't provide strong enough ground route to the others. From my observations, I've seen something around 5 ohm on average.
However, I have had one falcon that never glitched whatsoever. So I connected one of the other GND pads (the one next to VCC) and it's all good now.
Cheers
I noticed that during breaking the PCB panels of Rev B, the copper may or may not be "wide" enough (as in the distance between the pads and edges).
The consequence of this is minimal: the lower GND pad (near the LPT pads) is weakened and doesn't provide strong enough ground route to the others. From my observations, I've seen something around 5 ohm on average.
However, I have had one falcon that never glitched whatsoever. So I connected one of the other GND pads (the one next to VCC) and it's all good now.
Cheers
↧
Xbox Slim 1 Red Light
I have an xbox 360 Slim with trinity mobo, dash 14699... my problem is 1RedLight error 0032 :(
Fans and dvd drive still works! but no video/audio.
FAQS
1-Original nand
2-No rgh
3-I have CPU KEY and DVD KEY
4-Hanna point was repaired before.
Fans and dvd drive still works! but no video/audio.
FAQS
1-Original nand
2-No rgh
3-I have CPU KEY and DVD KEY
4-Hanna point was repaired before.
↧
NE555 selfmade squirt smc reset
hey guys.
i want to make my own smc reset for squirt, because i dont like QSB and for me it cost under 1€ when im make it self :p
here is the wiring diagram that i make.
![]()
but i need to know the size for C1 and R1 in my diagram(C2 is 10 nF), that is on the qsb nand pcb. can anyone with it, grab a multimeter and look what size the C1, C2 and R1 have? :)
and the voltage, i think it becomes 3.3V, but in datasheet there is a MIN. voltage from 4.5V? it will work corectly with 3.3V?
the IC become from the sync button a low signal(0V), and goes to squirt also a low signal oder a high signal when sync button is pressed?
thanks for help:D
EDIT: the NE7555 cmos version works with min. 3V but is the NE555 on the pcb? because the 4.5V min. :/
i want to make my own smc reset for squirt, because i dont like QSB and for me it cost under 1€ when im make it self :p
here is the wiring diagram that i make.
but i need to know the size for C1 and R1 in my diagram(C2 is 10 nF), that is on the qsb nand pcb. can anyone with it, grab a multimeter and look what size the C1, C2 and R1 have? :)
and the voltage, i think it becomes 3.3V, but in datasheet there is a MIN. voltage from 4.5V? it will work corectly with 3.3V?
the IC become from the sync button a low signal(0V), and goes to squirt also a low signal oder a high signal when sync button is pressed?
thanks for help:D
EDIT: the NE7555 cmos version works with min. 3V but is the NE555 on the pcb? because the 4.5V min. :/
↧
↧
Lifted CPU RST on the 360 Squirt glitcher itself .
i lifted the cpu point on my 360 squirt glitcher and now i can't make cip to glitch even with cpu_rst_r . Is there any solution for this ? thank you .
↧
i need install squirt nand instead original nand (original nand broken)
can do that? original dump i have.
slim trinity
no need dual nand. need work one nand for rgh.
if connect RE and CE to squirt nand (no squirt chip) its write? need 10 kom resistor for re point?
slim trinity
no need dual nand. need work one nand for rgh.
if connect RE and CE to squirt nand (no squirt chip) its write? need 10 kom resistor for re point?
↧
Alternate points for 1.2 BGA chip
If you have messed up a pad on the squirt 1.2bga you can use this image to see alternate points..
http://www.x360world.com/squirt/pinnedout.jpg
hope this helps someone
http://www.x360world.com/squirt/pinnedout.jpg
hope this helps someone
↧
Problem Slim trinity ... Xell reloaded don't work.
Hi, first, sry for my bad english.
I have solder a 360 squirt BGA 1.2 on my slim trinity (13599)
I solder all for SPI and RGH, look my picture. I have put 2 wires for GND, VCC, and make a bridge with punt 4 and VCC (cause i don't use second nand), i bridge too 220pF
for the RGH, i used CPU_RST (not cpu_rst_r)
With URJTAG.exe, i programmed the chip with a SVF... (i take trinity_bga_alwayson_120522_1450.svf) IT'S GOOD ??? OR I NEED TO TAKE AN OTHER ???
after, i used squirter.exe and dump my nand (PC->USB->programmer squirt->FLAT->360 squirt->SPI motherboard). So here, i have a strange problem. squirter tell me : bad connection to nand a lot (maybe 8,10 times) and after dump my nand O_o!! same problem for second dump.... So i have make 5 dump and use a compare nand to check that. NO ONE was the same !!! omg... So i tell me : F***ing wires !! i put out all SPI wires of the 360 squirt and use directly the programmer to dump (PC->USB->programmer squirt->SPI motherboard) and this times, it's works PERFECTLY, Nand respond directly, i dump 5x and all was the same.
So, i decide to create the ECC, and I flashed it using squirter.exe
Writing was ok. So i turning on the xbox360 (HDMI cable used to tv, not rgb). The 360 squirt led turning on and off normally (i think it s good) and the led of the front ring turning off and on very quickly (i saw on a youtube video that it's normal) but i m waiting more than 2 minutes and nothing...
After that, I have changed the SVF, with trinity_bga_120305_1226.svf, i have too used cpu_rst_r, i have "double" all my wires, i redid again the ECC and reflash, nothing happens... Xell reloaded don't appears...
PLEASE HELP ME. someone have an idea ? Someone can tell what the good setting ?
Which SVF ? Which cpu_rst ? Which lenght of wires for cpu_rst ? Which pF for resistor ? bridge Punt 4 and Vcc is ok ???
PLEASEEEEEEE :'(
![Name: 360squirtjon2.jpg
Views: 2
Size: 107.3 KB]()
![Name: 360squirtjon3.jpg
Views: 3
Size: 108.5 KB]()
I have solder a 360 squirt BGA 1.2 on my slim trinity (13599)
I solder all for SPI and RGH, look my picture. I have put 2 wires for GND, VCC, and make a bridge with punt 4 and VCC (cause i don't use second nand), i bridge too 220pF
for the RGH, i used CPU_RST (not cpu_rst_r)
With URJTAG.exe, i programmed the chip with a SVF... (i take trinity_bga_alwayson_120522_1450.svf) IT'S GOOD ??? OR I NEED TO TAKE AN OTHER ???
after, i used squirter.exe and dump my nand (PC->USB->programmer squirt->FLAT->360 squirt->SPI motherboard). So here, i have a strange problem. squirter tell me : bad connection to nand a lot (maybe 8,10 times) and after dump my nand O_o!! same problem for second dump.... So i have make 5 dump and use a compare nand to check that. NO ONE was the same !!! omg... So i tell me : F***ing wires !! i put out all SPI wires of the 360 squirt and use directly the programmer to dump (PC->USB->programmer squirt->SPI motherboard) and this times, it's works PERFECTLY, Nand respond directly, i dump 5x and all was the same.
So, i decide to create the ECC, and I flashed it using squirter.exe
Writing was ok. So i turning on the xbox360 (HDMI cable used to tv, not rgb). The 360 squirt led turning on and off normally (i think it s good) and the led of the front ring turning off and on very quickly (i saw on a youtube video that it's normal) but i m waiting more than 2 minutes and nothing...
After that, I have changed the SVF, with trinity_bga_120305_1226.svf, i have too used cpu_rst_r, i have "double" all my wires, i redid again the ECC and reflash, nothing happens... Xell reloaded don't appears...
PLEASE HELP ME. someone have an idea ? Someone can tell what the good setting ?
Which SVF ? Which cpu_rst ? Which lenght of wires for cpu_rst ? Which pF for resistor ? bridge Punt 4 and Vcc is ok ???
PLEASEEEEEEE :'(
↧
↧
PostBit trace F******. Please Help!!!
Hi!!!!
Everybody!!!!!
I f***** the PostBit trace. Have how to fix it?
The xbox is corona 4Gb and still working (without red light) but in the nand have Ecc codes the console don't show image on screen.
Thanks!!!!
Everybody!!!!!
I f***** the PostBit trace. Have how to fix it?
The xbox is corona 4Gb and still working (without red light) but in the nand have Ecc codes the console don't show image on screen.
Thanks!!!!
↧
Squirt Dual NAND - second nand don't work
Hello every one.
I have trouble applying second nand. First I install RGH hack with squirt BGA. Then decide to make it dual nand. I have install all the wires, but every time when I try to program the secandary NAND it seemd to program the original one.
Here are pictures from the installation :![Name: IMG_20121020_124920.jpg
Views: 12
Size: 98.0 KB]()
![Name: IMG_20121020_124931.jpg
Views: 14
Size: 96.3 KB]()
I try the two options - one if the secondary nand is empty and the other when it is previously flashed :
FIRST TIME NAND READING (your secondary NAND is empty):
- To enable the SECONDARY reading/writting (RGH ON):
> Disconnect the power cable of your console
> Press the SYNC BUTTON and re-connect the power cable.
> Release the SYNC BUTTON and power on the console with power button...
the fun will start very fast... Turn off again the console
> Start the writting / reading of secondary nand
READING / WRITTING NANDS when FREEBOOT is already installed on SECONDARY NAND:
- To enable the reading / writting of SECONDARY nand (RGH ON):
> disconnect and re-connect the power of your console
> start reading / writting of the original NAND.
But nothing worked every time I flashed the original one.
Am I missing something. The chip is flashed with SQUIRT__Corona_minusone_nr.svf. Do I need to use other file, or update the beetstream?
If some one can help I will be grateful.
I have trouble applying second nand. First I install RGH hack with squirt BGA. Then decide to make it dual nand. I have install all the wires, but every time when I try to program the secandary NAND it seemd to program the original one.
Here are pictures from the installation :
I try the two options - one if the secondary nand is empty and the other when it is previously flashed :
FIRST TIME NAND READING (your secondary NAND is empty):
- To enable the SECONDARY reading/writting (RGH ON):
> Disconnect the power cable of your console
> Press the SYNC BUTTON and re-connect the power cable.
> Release the SYNC BUTTON and power on the console with power button...
the fun will start very fast... Turn off again the console
> Start the writting / reading of secondary nand
READING / WRITTING NANDS when FREEBOOT is already installed on SECONDARY NAND:
- To enable the reading / writting of SECONDARY nand (RGH ON):
> disconnect and re-connect the power of your console
> start reading / writting of the original NAND.
But nothing worked every time I flashed the original one.
Am I missing something. The chip is flashed with SQUIRT__Corona_minusone_nr.svf. Do I need to use other file, or update the beetstream?
If some one can help I will be grateful.
↧
trinity strange dualboot problem
hi,
i have try to flash a new hacked image on secondary nand. i have turn on and off the console to select secondary nand. it write it and the xbox turns on with the OLD image :( i have hold the sync button and turn it on and i hear the xbox is reseting after 5 secs, after few times the squirt starts blinking and the old image start also. i think it has write the hacked image on orig nand :( i try to reflash but against flash config 0x023000... i think the nand was write corrupt and need a bad flash fix?
thanks for help..
i have try to flash a new hacked image on secondary nand. i have turn on and off the console to select secondary nand. it write it and the xbox turns on with the OLD image :( i have hold the sync button and turn it on and i hear the xbox is reseting after 5 secs, after few times the squirt starts blinking and the old image start also. i think it has write the hacked image on orig nand :( i try to reflash but against flash config 0x023000... i think the nand was write corrupt and need a bad flash fix?
thanks for help..
↧
New to this need help
I got my console rghd from a dealer sm days ago! I booted xell and got the cpu key but got the dvd key as all 0. Whats wrong? I am on 15574 glitched dash on corona v2. Can i get and use the current nand dump for future dash updates! I dont have original nand dump. Also can i dump the nand over ip by using autogg?thx fr listening!:)
↧
↧
Corona 16MB timing files for 360Squirt
Hi, does anyone know what the best timing files are supposed to be for 360Squirt in Corona 16MB?
Currently I'm getting very bad glitch times with rgh_corona_minusone_nr(suggested).svf. I've tested a fgew others with the same results.
Currently I'm getting very bad glitch times with rgh_corona_minusone_nr(suggested).svf. I've tested a fgew others with the same results.
↧
Programming the chip
I hope this is the right section...
So first off, I live in Canada. I've thought about getting the programmer but can't find any Canadian retailers and shipping comes out to an extra $30 on top of the already $25 cost. I'm looking into finding alternatives that are Canadian based which wouldn't cost as much for shipping.
I also have NO soldering skill so that's out of question.
So first off, I live in Canada. I've thought about getting the programmer but can't find any Canadian retailers and shipping comes out to an extra $30 on top of the already $25 cost. I'm looking into finding alternatives that are Canadian based which wouldn't cost as much for shipping.
I also have NO soldering skill so that's out of question.
↧
Couple of Q's regarding Corona
Ok successfully installed my first Squirt360 1.2 (Black pcb) all working fine and having been a TX user for a long time it is so much easier to have everything all in one and leave it all installed.
1, Glitch times, averaging around 20-30 seconds but occasionally hits around a minute, is it worth playing around to lessen the boot times or are they decent times for a corona? (using minusone)
2, Cable from the chip to the programmer, I have left installed and rerouted through the hdd bay (fits nice n snug with hdd installed), will there be any problem with this or is there a better route?
Also as per Q2 what would be best are to route cable in a phat?
Thanks in advance
1, Glitch times, averaging around 20-30 seconds but occasionally hits around a minute, is it worth playing around to lessen the boot times or are they decent times for a corona? (using minusone)
2, Cable from the chip to the programmer, I have left installed and rerouted through the hdd bay (fits nice n snug with hdd installed), will there be any problem with this or is there a better route?
Also as per Q2 what would be best are to route cable in a phat?
Thanks in advance
↧