I've installed the Squirt360 with the Dual Nand.. When the Console need to update (MS Update) it resets it's self. make the update fail leaving a Red Dot...
How to you stop this.. ???
How to you stop this.. ???
↧
MS Console Update Question???
↧
Help to find best config to Glitch corona using ft3t10 for cpu_rst
My first time doing a 360 rgh with DN however the system is not glitch even after 10 mins. can't figure out whats wrong.
my config as followed
-corona mb
-lifted ft3t10 and trace repair(as shown) and cpu_rst connected
-lifted r4p4 and trace repair
-lifted c5r11
-lifted postbit but manage to still solder on to the underside
-55cm awg 30 220pf used for cpu_rst
-using SQUIRT_Corona_dualnand_-1_3_120717_0953
-manage to retrieve cpukey during first attempt however connected to c5r11 instead of ft3t10
-able to read/write original nand
-able to read/write secondary nand
-able to boot to original nand on 14719
-secondary nand flashed with 14719 image created using autogg 0.7
![Name: IMG_19782.jpg
Views: 40
Size: 102.9 KB]()
Please help! thank you!
my config as followed
-corona mb
-lifted ft3t10 and trace repair(as shown) and cpu_rst connected
-lifted r4p4 and trace repair
-lifted c5r11
-lifted postbit but manage to still solder on to the underside
-55cm awg 30 220pf used for cpu_rst
-using SQUIRT_Corona_dualnand_-1_3_120717_0953
-manage to retrieve cpukey during first attempt however connected to c5r11 instead of ft3t10
-able to read/write original nand
-able to read/write secondary nand
-able to boot to original nand on 14719
-secondary nand flashed with 14719 image created using autogg 0.7
Please help! thank you!
↧
↧
Squirt Dual Nand on Slim.. no power?
I just install a Dual nand to a slim, but when I power on It just Beeps? no power no boot.. if i remove it and Squirt BGA(power to BGA it boots Original dash fine.. this is the 2nd one i've installed.
![]()
![]()
![]()
↧
RGH 2.0 Cant get it :S
I have an xbox 360 (Jasper) Dash 14719, Im trying to do RGH 2.0 but i cant get the dashboard when the console is totally closed (RGH Done) any ideas?
How to get the best booting time? any ideas about where to put the cpu reset cable?
Help Guys! I need it :)
P.S im using 360 Squirt
How to get the best booting time? any ideas about where to put the cpu reset cable?
Help Guys! I need it :)
P.S im using 360 Squirt
↧
how to check bga 1.2 is faulty?
Hi guys
how can i check if the chip is faulty?
how can i check if the chip is faulty?
↧
↧
Using Dual nand 16MB...but console is 512 MB jasper?
Is this a problem? Because as far as I know the glitch image can be made 16 or 256 or 512...I thought it flashes first 16 MB alone if necessary. I already have cpukey, fuses...etc.
Its a jasper 512, squirt 16MB nand and (another brand) coolruner...not having much luck...btw with a external switch and dash is 13599. No luck at all...
Its a jasper 512, squirt 16MB nand and (another brand) coolruner...not having much luck...btw with a external switch and dash is 13599. No luck at all...
↧
Solved issue of TDO stuck at 1 when LPT programming
After a little nervous disaster with trying to program SQUIRT (Black) with the LPT solution provided, I cooled down (use a beer if you have one), and found the problem : the GND point at LPT needs to be connected with GND point on the upper side of the board, or use GND and Vcc both on the upper side to power the chip IF you power it from your PC. Bottom line:if you don't have continuity between the 2 points, connect the dots (disconnect them after programming). And use AutoGG ONLY (tried others and they still give TDO errors).
↧
What do I need to install a Squirt360 into a Corona (250gb)?
Hi,
I'm familiar with installing modchips (going to the PSX days), but have only done 2 RGH's.
One phat, and one slim - I used Matrix Glitcher v2's.
They were both pretty simple installs.
I now have 2 Corona 250gb's to do, and will be ordering a couple of Squirt360's.
Previously I used a Nand-X (v3) to read and write the onboard Nand, and the Matrix's did not require programming.
What do I need (if anything), other than the Squirt360's themselves.
Also are there any differences between the older machines and new Coronas when installing the chips...
(I believe Xell does not show on the TV, and you must access the webserver via http (browser) to get the CpuKey).
Thanks
I'm familiar with installing modchips (going to the PSX days), but have only done 2 RGH's.
One phat, and one slim - I used Matrix Glitcher v2's.
They were both pretty simple installs.
I now have 2 Corona 250gb's to do, and will be ordering a couple of Squirt360's.
Previously I used a Nand-X (v3) to read and write the onboard Nand, and the Matrix's did not require programming.
What do I need (if anything), other than the Squirt360's themselves.
Also are there any differences between the older machines and new Coronas when installing the chips...
(I believe Xell does not show on the TV, and you must access the webserver via http (browser) to get the CpuKey).
Thanks
↧
TDO seems tobe stucks at 1...Again
Hi, I'm a new member.
I have finally decided to mod my xbox360 fat (falcon) with RGH.
I'm finding a lot of problems.
I bought:
X360 SQUIRT COOL RUNNER BGA 1.2
X360 SQUIRT SLAVE PROGRAMMER SPI NAND
So I connected everything and ...
UrJTAG says TDO Seems to be stuck at 1. So I try AutoGG the same. Another PC, same. Another USB cable, the same. I try to push it with my thumb on BGA, the same.
I call the seller and he refund me.
Now I bought a new bga by another seller, and now: THE SAME ERROR.
I have also tried using LPT cable (without slave programmer), but ... Seems i had TDO .... bla bla ...
I'm devastated.
How can this happen?
What can I do?
Please help me.
Drivers are ok, flat cable ok, lpt cable ok...
What is the probability to get two of 2 faulty BGA?
I have finally decided to mod my xbox360 fat (falcon) with RGH.
I'm finding a lot of problems.
I bought:
X360 SQUIRT COOL RUNNER BGA 1.2
X360 SQUIRT SLAVE PROGRAMMER SPI NAND
So I connected everything and ...
UrJTAG says TDO Seems to be stuck at 1. So I try AutoGG the same. Another PC, same. Another USB cable, the same. I try to push it with my thumb on BGA, the same.
I call the seller and he refund me.
Now I bought a new bga by another seller, and now: THE SAME ERROR.
I have also tried using LPT cable (without slave programmer), but ... Seems i had TDO .... bla bla ...
I'm devastated.
How can this happen?
What can I do?
Please help me.
Drivers are ok, flat cable ok, lpt cable ok...
What is the probability to get two of 2 faulty BGA?
↧
↧
360 squirt warranty?
I Just buy a 360 Squirt and came out with a manufacturing defect, Is not glitching any console (FAT or SLIM), Already flashed with all the bitstreams and the chip is like turned off (No led)
also i bought a PCB 16mb Nand, but this one is also defective, Because I tested with multimeter and it gives me electrical continuity at some points (obviously causing an electrical short)
Question
360 Squirt warranty? i bought trough VGC Repairs.
Please im so sad :(
This is not an installation issue, because i already made like 25 xbox 360 and I already used 360 squirt before.
also i bought a PCB 16mb Nand, but this one is also defective, Because I tested with multimeter and it gives me electrical continuity at some points (obviously causing an electrical short)
Question
360 Squirt warranty? i bought trough VGC Repairs.
Please im so sad :(
This is not an installation issue, because i already made like 25 xbox 360 and I already used 360 squirt before.
↧
Help me update dual-boot please
hello,
I have a dual boot Slim trinity at 14719 with the bga black 1.2 and dual nand.
It has the "trinity_bga_120305_1226.svf" on the chip.
I updated the stock image through LIVE to 15574 and I want to dump my stock nand now in order to build the hacked image but I can't seem to get it right...
I connect the xbox to power, read with squirter but when i load the bin with J-runner it still shows 14719 ...so I'm guessing i'm reading the hacked nand ?
How can I read the stock nand ?
Also ..should I update the svf too ?
Thanks
EDIT:
Ok I managed to update both stock and hacked image and everything is working good.
I pressed the sync while pluging in the power ..and had access to the stock image (the other way around from when first installing) .. and if i just pluged the power and read I had access the the hacked image.
One sidenote if oneone stumbles on this problem: be sure to remove the programmer's usb cable as it feeds a little power to the chip and selecting the nands with the above method doesnt work.
I have a dual boot Slim trinity at 14719 with the bga black 1.2 and dual nand.
It has the "trinity_bga_120305_1226.svf" on the chip.
I updated the stock image through LIVE to 15574 and I want to dump my stock nand now in order to build the hacked image but I can't seem to get it right...
I connect the xbox to power, read with squirter but when i load the bin with J-runner it still shows 14719 ...so I'm guessing i'm reading the hacked nand ?
How can I read the stock nand ?
Also ..should I update the svf too ?
Thanks
EDIT:
Ok I managed to update both stock and hacked image and everything is working good.
I pressed the sync while pluging in the power ..and had access to the stock image (the other way around from when first installing) .. and if i just pluged the power and read I had access the the hacked image.
One sidenote if oneone stumbles on this problem: be sure to remove the programmer's usb cable as it feeds a little power to the chip and selecting the nands with the above method doesnt work.
↧
corona v2 problem
i read the nand and create a ecc with the new autogg
write it to the nand but the console dont boot
plz help
i just need to disconnect all the wire
and the next time i use switch
write it to the nand but the console dont boot
plz help
i just need to disconnect all the wire
and the next time i use switch
↧
glitch using bga 1.2 svf however unable to glitch using dual nand svf
I can get a consistent booting with SQUIRT__Corona_addone_r.svf
however when I use both dual nand bitstreams i can't seems to glitch the xbox at all.
any idea i can troubleshoot this?
thank you
however when I use both dual nand bitstreams i can't seems to glitch the xbox at all.
any idea i can troubleshoot this?
thank you
↧
↧
Dual nand with other glitch chip?¡
It is possible? use a cool runner with the squirt pcb 16mb nand, to get a dual nand xbox 360?¡
↧
Crazy 512mb Jasper Update Problem! RGH 2.0
Hi all, I'm in need of your help. Basically I had the big block Jasper booting fine. I threw a backup copy of Tekken Tag Tournament 2 in to test the drive mod. It showed up, but then it asked me for an update. Well apparently this is the first game to contain the 15574 Dash update, as the console was running the newest freeboot. So I said ok to the update as it was just the avatar update. the first half of the update went fine, but when it restarted to continue the update, it said dirty disc, unable to update. Any way, now it throws e71 without the disc in the drive when I attempt to boot it, and it gives me the dirty disc error if it's in the console. Updating from usb and regular dvd have both resulted in cannot process updates errors. Really need help to sort this out. By the way, I have two matching 64mb dumps, not 512mb. Thanks
↧
New to RGH with at problem with v1.2 and Trinity
I I have just made my first install of a 360 squirt black v1.2 and I have never been J-tagging or rgh before.
I now can read the nand. Create Xell and flash the Xell, but when I turn the thing on, I just get a red light in front of the xbox.
I dont know where to start searching for my problem, all the soldering seems to be fine, but there are different install manual out there on the squirt360 website.
Any ideas on where to start?
I now can read the nand. Create Xell and flash the Xell, but when I turn the thing on, I just get a red light in front of the xbox.
I dont know where to start searching for my problem, all the soldering seems to be fine, but there are different install manual out there on the squirt360 website.
Any ideas on where to start?
↧
Downloads section
All the Squirt files can be found in the Download section on this site ... You must be a member to download..
I have everything up to date as of today , and I have added other downloads as well.
Thank You
Juggahaxor
I have everything up to date as of today , and I have added other downloads as well.
Thank You
Juggahaxor
↧
↧
Question Regarding Dual Nand Install with Squirt Green Board
So I decided to dust off this old Squirt green edition board to attempt a dual nand with some of my extra nand pcbs. Anyway, it works, but not consistently. I can only get it into the retail nand if I pull the power and reconnect first. Otherwise it just boot to RGH. Second, sometimes when I try to boot the RGH side it just goes to a red light. If I turn it off and back on it usually works just fine, but as of now I don't feel comfortable selling it as it sits. The tutorial did say that the code for the green squirt chips isn't perfect, but I'm wondering if any of you guys have experienced similar issues. Thanks
↧
Drivers for squirt slave programmer
Hi all! I bought squit360 BGA1.2 and squirt slave programmer . Now, I have been unable to find drivers to programmer. And I do not know how to programm my squirt360bga 1.2
Thanks
Thanks
↧
Help with RGH Not working.
I have Xbox 360 FAT (FALCON) D: 2.0.14719
Ive installed the 360 squirt glitch chip without CLK point. the console is glitching but never give me image (not booting)
I already have the cpukey but i cant get it :S
Any ideas about the setup?
CPU_R Cable cm? resistors? capacitors? where to put the cables? HELPPP Guys! :(
Ive installed the 360 squirt glitch chip without CLK point. the console is glitching but never give me image (not booting)
I already have the cpukey but i cant get it :S
Any ideas about the setup?
CPU_R Cable cm? resistors? capacitors? where to put the cables? HELPPP Guys! :(
↧